Re: station_cnt not work ?
Thank you for your response and sorry of this delay in my post :c Your commands works well and it works! Well.. I have a problem with this command in my SSH consol Whereas i write : iw wlan0 station...
View ArticleRaspberry pi 3 movie streaming
Hi I am quite new to piratebox and tried to stream movie from it but however it doesn't seem fast enough to stream the movie making it lag. Is there any way to make it run faster? Thanks
View ArticleRe: Raspberry pi 3 movie streaming
I have streamed movies previously from my MR3020 without problem and that hardware is weaker than a Raspberry. I have just tried again, streaming a ripped .avi to my phone, no lag at all. I don't...
View ArticleRe: Raspberry pi 3 movie streaming
Right now currently im using the normal wifi card on the raspberry pi 3 not sure if it is my usb drive slowing it down or my wifi card
View ArticleRe: Raspberry pi 3 movie streaming
Oh I forgot to tell you. The video I'm trying to stream is a 1280x720 around 20min long
View ArticleRPI3 and WIFI Config open question
Hello, I have made a RPI3 Pirate Box, everything is turning good at home. But tomorrow i want to take my pirate box in another place with the same architecture but for sure it will be not the same...
View ArticleRe: Re-sizing partition of SD card on Raspberry Pi(rate) Box
Launch GParted Change the drop-down to the device of the SD card Right-click on the partition to re-size, select "Unmount" Right-click on the partition to re-size and click "re-size/move". Drag the...
View ArticleRe: Custom User Interface + Multi-Directories Uploads [Pi(rate)Box 1.0]
Hi, I'd like to change the index page a bit, but try as I might I cannot get to the www folder. Do I have to access the image through ssh while piratebox is running, access the www file there and...
View ArticleRe: Custom User Interface + Multi-Directories Uploads [Pi(rate)Box 1.0]
it's the most recent image running on a pi 3, by the way. Also, I've had loads of fun setting this up. Thanks for all your hard work guys!
View ArticleRe: PirateBox 1.0.7 - RPi / RPi2 / RPi3 / RPi Zero
This image for the original RPi doesn't seem to have a package manager (apt/opkg/yum). It is supposed to?
View ArticleHelp! RPI3 with TP-Link TL-WN722N
Hello all, (Bare with me, new here!) I am new to this forum, and I would like some assistance if available. Long story short, I have successfully setup my raspberrypi 3 with Piratebox, and I have been...
View ArticleRe: Custom User Interface + Multi-Directories Uploads [Pi(rate)Box 1.0]
Hello again, I have figured out how to get top the file edit the html via nano in terminal using ssh, so at least I can see the files, but now |I cannot edit them as it's telling me that the they are...
View ArticleRe: RPI3 and WIFI Config open question
The PirateBox is a stand-alone system, it does not matter where you take it, you will have the same experience. The IP address will be the same. WiFi will work the same. No need to edit anything once...
View ArticleRe: Help! RPI3 with TP-Link TL-WN722N
You can check the interfaces you have with ifconfig This will show you the status of the currently active interfaces. From there you should be able to see which one is actually broadcasting the local...
View ArticleRe: Custom User Interface + Multi-Directories Uploads [Pi(rate)Box 1.0]
dave Wrote: ------------------------------------------------------- > Hi, > > I'd like to change the index page a bit, but try > as I might I cannot get to the www folder. Do I > have...
View ArticleRe: Raspberry pi 3 movie streaming
You can try t use another USB stick and see if it makes a difference. The network itself should be more than enough to stream a 720p movie, the length shouldn't be a limiting factor. I'm not sure if...
View ArticleRe: Help! RPI3 with TP-Link TL-WN722N
Doesn't look like it detects the external adapter at all. Only shows wlan0 and "lo" which I assume is the loopback address. Know of a way to make the adapter show up?
View ArticleRe: Help! RPI3 with TP-Link TL-WN722N
Depending on the version of the adapter (http://elinux.org/RPi_USB_Wi-Fi_Adapters) you may need a powered hub. Also, the driver may not be pre-installed.
View Article