Hostapd.conf is as follows:
interface=wlan1
driver=nl80211
ssid=PirateBox - Share Freely
hw_mode=g
channel=1
#auth_algs=1
#ieee80211n=1
And piratebox.conf:
#########
## Config for pirate-box WWW Release
## written by Matthias Strubel (matthias.strubel@aod-rpg.de) 2011-02-22
## licenced by gpl ; feel free to improve or send me feedback
##
## 2012-04-12 Created
## 2012-06-08 Changed IP Stuff to generating dnsmasq.conf stuff
## ADDed SubConfig for IPV6 config
## Changed Order of config
## 2013-08-14 Added timesave url
##
########
#######
## Configuration help
## If you plan to use one laptop as the piratebox:
## Set DO_IFCONFIG , USE_APN, USE_DNSMASQ to yes
## If you plan to run a two component setup (one router and one providing the storage+website)
## connected with ethernet:
## Set DO_IFCONFIG , USE_APN, USE_DNSMASQ to no
## Configure your ethernet eth0 (or whatever) to a static IP
## force your router to publish the HOST Option with your static IP; in case of dnsmasq add the /etc/hosts entrys
## Have a look at [wiki.daviddarts.com] for futher instructions
##
## You may deactivated severall option as needed. It's flexible.
#----------------- Folder Configuration -------------------#
PIRATEBOX_FOLDER="/opt/piratebox"
WWW_FOLDER="/opt/piratebox/www"
#Do not change untill really needed.
PIRATEBOX_PYTHONPATH="$PIRATEBOX_FOLDER/python_lib"
#Datafolder , where is you usb-stick // drive mounted
SHARE_FOLDER="$PIRATEBOX_FOLDER/share"
#Upload Folder
# Change this if you want to user uploaded data in a subfolder
# Make sure the folder exists
# UPLOADFOLDER="$SHARE_FOLDER/Upload"
UPLOADFOLDER="$SHARE_FOLDER/Shared"
#----------------- Startup Configuration -------------------#
# Which Steps has to be done
#Do network config
DO_IFCONFIG="yes"
#Do IW config - setting up a wlan0 interface with iw
# for some wifi-cards required
DO_IW="yes"
#Iw physical interface
PHY_IF="phy1"
# Check if interface exists
# should be set to yes if you use a USB wifi card
PROBE_INTERFACE="yes"
# wait how many seconds until throw an error
PROBE_TIME=10
#Start services...
# act like a apn / <yes|no>
# please have a look @ hostapd.conf ; you may need to change some options, regarding wifi-card
USE_APN="yes"
# act like dns&dhcp (dnsmasq)
USE_DNSMASQ="yes"
#HOSTNAME ... if you really want to change it, plz change:
# bin/droopy
# conf/hosts
HOST="piratebox.lan"
#----------------- Configuration for DNSMASQ & IF-Setup -------------------#
# Name of the wlan interface
INTERFACE="wlan1"
# On which interface DNSMASQ should listen. -i is the parameter for dnsmasq
# Make it empty to disable
DNSMASQ_INTERFACE="wlan1"
#Brdige add interfacce (setr yes to enable bridging)
DO_BRIDGE="no"
BRIDGE="br-lan"
#Network
NET=192.168.77
#IP-SHORT (is stringed together)
# Which IP is your Box?? i.e. 1 => 192.168.77.1
IP_SHORT=1
#DHCP LEASE Start
START_LEASE=10
#DHCP LEASE End Range
END_LEASE=250
#Leasetime (When should the client renew it's IP)
LEASE_DURATION=12h
# Where is the leasefile stored to?
LEASE_FILE_LOCATION=$PIRATEBOX_FOLDER/tmp/lease.file
# Define the netmask
NETMASK=255.255.255.0
#SET IP for ifconfig stuff - DON'T CHANGE
IP=$NET.$IP_SHORT
#Load Config about ipv6 stuff - DON'T CHANGE
. $PIRATEBOX_FOLDER/conf/ipv6.conf
#----------------- Configuration for the pure piratebox -------------------#
## droopy, webserver, shoutbox- and forum-server
## Timesave file for non RTC devices
TIMESAVE="$PIRATEBOX_FOLDER/share/timesave_file"
#On non OpenWRT you can use the default output format
# as an input format. For OpenWrt you need to specify +%C%g%m%d%H%M
# The content is exchanged during makefile processing and image build
TIMESAVE_FORMAT="+%C%g%m%d %H%M"
#Start droopy? - Enable upload?
DROOPY_ENABLED="yes"
#Image-SRC
IMAGENAME="piratebox-logo-small.png"
IMAGE="$PIRATEBOX_FOLDER/src/$IMAGENAME"
DROOPY_TXT=""
DROOPY_PORT="8080"
# Set correct permissions for an uploaded file
DROOPY_CHMOD="755"
DROOPY_USERDIR=""
# Uncomment line below for adding directory feature
#DROOPY_USERDIR=" -u True "
#Use UserId from lighttpd for droopy (use on ext-filesystems)
DROOPY_USE_USER="yes"
#Configuration for chat (If you decide to move the chat folder, you have to change /opt/piratebox/chat/cgi-bin/py* files )
CHATFILE="$WWW_FOLDER/cgi-bin/data.pso"
#Generated File
GEN_CHATFILE="$WWW_FOLDER/chat_content.html"
#Generated File for DiskUsage
GEN_DISKFILE="$WWW_FOLDER/diskusage.html"
# Reset Shoutbox on Startup?
RESET_CHAT="yes"
#Inititiation Chat-Message
CHATMSG="<div class='message'><date>00:00:00</date> <name>PirateBox:</name> <data class='def'>Chat and share files anonymously!</data></div>"
#Activate Global chat
# Still experimentall!
GLOBAL_CHAT="no"
#On which broadcast address should it send
# Take care on the syntax!!
GLOBAL_DEST="[ #255.255.255.255# , #10.255.255.255# , #$NET.255# ]"
#------------------------ Additional configuration for lighttpd
LIGHTTPD_USER=nobody
LIGHTTPD_GROUP=nogroup
#------------------------ Hook in user-config
. $PIRATEBOX_FOLDER/conf/hook_custom.conf
interface=wlan1
driver=nl80211
ssid=PirateBox - Share Freely
hw_mode=g
channel=1
#auth_algs=1
#ieee80211n=1
And piratebox.conf:
#########
## Config for pirate-box WWW Release
## written by Matthias Strubel (matthias.strubel@aod-rpg.de) 2011-02-22
## licenced by gpl ; feel free to improve or send me feedback
##
## 2012-04-12 Created
## 2012-06-08 Changed IP Stuff to generating dnsmasq.conf stuff
## ADDed SubConfig for IPV6 config
## Changed Order of config
## 2013-08-14 Added timesave url
##
########
#######
## Configuration help
## If you plan to use one laptop as the piratebox:
## Set DO_IFCONFIG , USE_APN, USE_DNSMASQ to yes
## If you plan to run a two component setup (one router and one providing the storage+website)
## connected with ethernet:
## Set DO_IFCONFIG , USE_APN, USE_DNSMASQ to no
## Configure your ethernet eth0 (or whatever) to a static IP
## force your router to publish the HOST Option with your static IP; in case of dnsmasq add the /etc/hosts entrys
## Have a look at [wiki.daviddarts.com] for futher instructions
##
## You may deactivated severall option as needed. It's flexible.
#----------------- Folder Configuration -------------------#
PIRATEBOX_FOLDER="/opt/piratebox"
WWW_FOLDER="/opt/piratebox/www"
#Do not change untill really needed.
PIRATEBOX_PYTHONPATH="$PIRATEBOX_FOLDER/python_lib"
#Datafolder , where is you usb-stick // drive mounted
SHARE_FOLDER="$PIRATEBOX_FOLDER/share"
#Upload Folder
# Change this if you want to user uploaded data in a subfolder
# Make sure the folder exists
# UPLOADFOLDER="$SHARE_FOLDER/Upload"
UPLOADFOLDER="$SHARE_FOLDER/Shared"
#----------------- Startup Configuration -------------------#
# Which Steps has to be done
#Do network config
DO_IFCONFIG="yes"
#Do IW config - setting up a wlan0 interface with iw
# for some wifi-cards required
DO_IW="yes"
#Iw physical interface
PHY_IF="phy1"
# Check if interface exists
# should be set to yes if you use a USB wifi card
PROBE_INTERFACE="yes"
# wait how many seconds until throw an error
PROBE_TIME=10
#Start services...
# act like a apn / <yes|no>
# please have a look @ hostapd.conf ; you may need to change some options, regarding wifi-card
USE_APN="yes"
# act like dns&dhcp (dnsmasq)
USE_DNSMASQ="yes"
#HOSTNAME ... if you really want to change it, plz change:
# bin/droopy
# conf/hosts
HOST="piratebox.lan"
#----------------- Configuration for DNSMASQ & IF-Setup -------------------#
# Name of the wlan interface
INTERFACE="wlan1"
# On which interface DNSMASQ should listen. -i is the parameter for dnsmasq
# Make it empty to disable
DNSMASQ_INTERFACE="wlan1"
#Brdige add interfacce (setr yes to enable bridging)
DO_BRIDGE="no"
BRIDGE="br-lan"
#Network
NET=192.168.77
#IP-SHORT (is stringed together)
# Which IP is your Box?? i.e. 1 => 192.168.77.1
IP_SHORT=1
#DHCP LEASE Start
START_LEASE=10
#DHCP LEASE End Range
END_LEASE=250
#Leasetime (When should the client renew it's IP)
LEASE_DURATION=12h
# Where is the leasefile stored to?
LEASE_FILE_LOCATION=$PIRATEBOX_FOLDER/tmp/lease.file
# Define the netmask
NETMASK=255.255.255.0
#SET IP for ifconfig stuff - DON'T CHANGE
IP=$NET.$IP_SHORT
#Load Config about ipv6 stuff - DON'T CHANGE
. $PIRATEBOX_FOLDER/conf/ipv6.conf
#----------------- Configuration for the pure piratebox -------------------#
## droopy, webserver, shoutbox- and forum-server
## Timesave file for non RTC devices
TIMESAVE="$PIRATEBOX_FOLDER/share/timesave_file"
#On non OpenWRT you can use the default output format
# as an input format. For OpenWrt you need to specify +%C%g%m%d%H%M
# The content is exchanged during makefile processing and image build
TIMESAVE_FORMAT="+%C%g%m%d %H%M"
#Start droopy? - Enable upload?
DROOPY_ENABLED="yes"
#Image-SRC
IMAGENAME="piratebox-logo-small.png"
IMAGE="$PIRATEBOX_FOLDER/src/$IMAGENAME"
DROOPY_TXT=""
DROOPY_PORT="8080"
# Set correct permissions for an uploaded file
DROOPY_CHMOD="755"
DROOPY_USERDIR=""
# Uncomment line below for adding directory feature
#DROOPY_USERDIR=" -u True "
#Use UserId from lighttpd for droopy (use on ext-filesystems)
DROOPY_USE_USER="yes"
#Configuration for chat (If you decide to move the chat folder, you have to change /opt/piratebox/chat/cgi-bin/py* files )
CHATFILE="$WWW_FOLDER/cgi-bin/data.pso"
#Generated File
GEN_CHATFILE="$WWW_FOLDER/chat_content.html"
#Generated File for DiskUsage
GEN_DISKFILE="$WWW_FOLDER/diskusage.html"
# Reset Shoutbox on Startup?
RESET_CHAT="yes"
#Inititiation Chat-Message
CHATMSG="<div class='message'><date>00:00:00</date> <name>PirateBox:</name> <data class='def'>Chat and share files anonymously!</data></div>"
#Activate Global chat
# Still experimentall!
GLOBAL_CHAT="no"
#On which broadcast address should it send
# Take care on the syntax!!
GLOBAL_DEST="[ #255.255.255.255# , #10.255.255.255# , #$NET.255# ]"
#------------------------ Additional configuration for lighttpd
LIGHTTPD_USER=nobody
LIGHTTPD_GROUP=nogroup
#------------------------ Hook in user-config
. $PIRATEBOX_FOLDER/conf/hook_custom.conf